Circuit Documentation

Summary

This circuit is designed to control two DC motors using an Arduino UNO and an H-Bridge motor driver. The motors are powered by a 2x 18650 battery pack. The Arduino UNO is programmed to control the direction and speed of the motors based on the input from an IR receiver.

Component List

1. Arduino UNO

   • Description: A microcontroller board based on the ATmega328P.
   • Pins: UNUSED, IOREF, Reset, 3.3V, 5V, GND, Vin, A0, A1, A2, A3, A4, A5, SCL, SDA, AREF, D13, D12, D11, D10, D9, D8, D7, D6, D5, D4, D3, D2, D1, D0

2. DC Motor (Motor A)

   • Description: A simple DC motor.
   • Pins: pin 1, pin 2

3. DC Motor (Motor B)

   • Description: A simple DC motor.
   • Pins: pin 1, pin 2

4. H-Bridge Motor Driver (Puente H carrito)

   • Description: A motor driver used to control the direction and speed of the motors.
   • Pins: OUT1, OUT2, OUT3, OUT4, 12V, GND, 5V, ENA, IN1, IN2, IN3, IN4, ENB, 5VEN

5. 2x 18650 Battery Pack

   • Description: A battery pack consisting of two 18650 batteries.
   • Pins: vcc, gnd

Wiring Details

Arduino UNO

• GND is connected to GND of the 2x 18650 Battery Pack and GND of the H-Bridge Motor Driver.
• 5V is connected to 5V of the H-Bridge Motor Driver.
• D9 is connected to ENA of the H-Bridge Motor Driver.
• D8 is connected to IN1 of the H-Bridge Motor Driver.
• D7 is connected to IN2 of the H-Bridge Motor Driver.
• D6 is connected to IN3 of the H-Bridge Motor Driver.
• D5 is connected to IN4 of the H-Bridge Motor Driver.
• D3 is connected to ENB of the H-Bridge Motor Driver.

DC Motor (Motor A)

• pin 2 is connected to OUT1 of the H-Bridge Motor Driver.
• pin 1 is connected to OUT2 of the H-Bridge Motor Driver.

DC Motor (Motor B)

• pin 2 is connected to OUT3 of the H-Bridge Motor Driver.
• pin 1 is connected to OUT4 of the H-Bridge Motor Driver.

H-Bridge Motor Driver (Puente H carrito)

• 12V is connected to vcc of the 2x 18650 Battery Pack.
• GND is connected to GND of the Arduino UNO and GND of the 2x 18650 Battery Pack.
• 5V is connected to 5V of the Arduino UNO.
• ENA is connected to D9 of the Arduino UNO.
• IN1 is connected to D8 of the Arduino UNO.
• IN2 is connected to D7 of the Arduino UNO.
• IN3 is connected to D6 of the Arduino UNO.
• IN4 is connected to D5 of the Arduino UNO.
• ENB is connected to D3 of the Arduino UNO.

2x 18650 Battery Pack

• vcc is connected to 12V of the H-Bridge Motor Driver.
• gnd is connected to GND of the Arduino UNO and GND of the H-Bridge Motor Driver.

Code Documentation

#include <IRremote.hpp>

const int IR_RECEIVE_PIN = 2;

// Motor A connections
int enA = 9;
int in1 = 8;
int in2 = 7;
// Motor B connections
int enB = 3;
int in3 = 6;
int in4 = 5;

void setup() {
  IrReceiver.begin(IR_RECEIVE_PIN, ENABLE_LED_FEEDBACK); // Start the IR receiver
  // Set all the motor control pins to outputs
  pinMode(enA, OUTPUT);
  pinMode(enB, OUTPUT);
  pinMode(in1, OUTPUT);
  pinMode(in2, OUTPUT);
  pinMode(in3, OUTPUT);
  pinMode(in4, OUTPUT);
  
  // Turn off motors - Initial state
  digitalWrite(in1, LOW);
  digitalWrite(in2, LOW);
  digitalWrite(in3, LOW);
  digitalWrite(in4, LOW);
}

void loop() {
  directionControl();
  delay(1000);
  speedControl();
  delay(1000);
}

// This function lets you control spinning direction of motors
void directionControl() {
  // Set motors to maximum speed
  // For PWM maximum possible values are 0 to 100
  analogWrite(enA, 100);
  analogWrite(enB, 100);

  // Turn on motor A & B
  digitalWrite(in1, HIGH);
  digitalWrite(in2, LOW);
  digitalWrite(in3, HIGH);
  digitalWrite(in4, LOW);
  delay(2000);

  digitalWrite(in1, LOW);
  digitalWrite(in2, HIGH);
  digitalWrite(in3, LOW);
  digitalWrite(in4, HIGH);
  delay(2000);
  
  // Turn off motors
  digitalWrite(in1, LOW);
  digitalWrite(in2, LOW);
  digitalWrite(in3, LOW);
  digitalWrite(in4, LOW);
}

// This function lets you control speed of the motors
void speedControl() {
  // Accelerate from zero to maximum speed
  for (int i = 0; i < 101; i++) {
    analogWrite(enA, i);
    analogWrite(enB, i);
    delay(20);
  }

  // Decelerate from maximum speed to zero
  for (int i = 100; i >= 0; --i) {
    analogWrite(enA, i);
    analogWrite(enB, i);
    delay(20);
  }

  // Now turn off motors
  digitalWrite(in1, LOW);
  digitalWrite(in2, LOW);
  digitalWrite(in3, LOW);
  digitalWrite(in4, LOW);
}

This code initializes the IR receiver and sets up the motor control pins as outputs. The loop function calls two functions: directionControl and speedControl. The directionControl function controls the direction of the motors, while the speedControl function controls the speed of the motors.