Cirkit Designer LogoCirkit DesignerYour all-in-one circuit design IDE Launch Cirkit Designer App

Arduino UNO-Based Color Sorting Machine with Traffic Light and Seven Segment Display

View and Edit Project In Cirkit DesignerImage of Arduino UNO-Based Color Sorting Machine with Traffic Light and Seven Segment Display

Circuit Documentation

Summary

This circuit is a color sorting machine that uses an Arduino UNO microcontroller to control a seven-segment display, a traffic light, a piezo speaker, and a servo motor (MG996R). The Arduino UNO reads color values from a color sensor and sorts objects based on their color. The seven-segment display shows the color values, the traffic light indicates the status, and the piezo speaker provides audio feedback.

Component List

  1. Arduino UNO

    • Description: A microcontroller board based on the ATmega328P.
    • Pins: UNUSED, IOREF, Reset, 3.3V, 5V, GND, Vin, A0, A1, A2, A3, A4, A5, SCL, SDA, AREF, D13, D12, D11, D10, D9, D8, D7, D6, D5, D4, D3, D2, D1, D0

  2. Traffic Light

    • Description: A traffic light module with three LEDs (Green, Yellow, Red) and a ground pin.
    • Pins: Green, Yellow, Red, GND

  3. Piezo Speaker

    • Description: A piezoelectric speaker for generating sound.
    • Pins: pin1, pin2

  4. MG996R Servo Motor

    • Description: A high-torque servo motor.
    • Pins: GND, VCC, SIG

  5. Seven Segment Display (Wokwi Compatible)

    • Description: A seven-segment display for showing numerical values.
    • Pins: G, F, COM.2, B, A, E, D, COM.1, C, DP

  6. Resistors

    • Description: Various resistors used for current limiting.
    • Pins: pin1, pin2
    • Properties:
      • Resistance: 200 Ohms (5 instances)
      • Resistance: 220 Ohms (1 instance)

Wiring Details

Arduino UNO

Traffic Light

Piezo Speaker

MG996R Servo Motor

Seven Segment Display (Wokwi Compatible)

Resistors

Documented Code

/*Color Sorting Machine by : Omar Wael Morsi*/
/*YouTube : Morsi Hamed  https://www.youtube.com/c/morsihamed */

#include <Servo.h>
#define S0 2
#define S1 3
#define S2 4
#define S3 5
#define sensorOut 6
Servo topServo;
Servo bottomServo;
int frequency = 0;
int color = 0;

void setup() {
  pinMode(S0, OUTPUT);
  pinMode(S1, OUTPUT);
  pinMode(S2, OUTPUT);
  pinMode(S3, OUTPUT);
  pinMode(sensorOut, INPUT); 
  digitalWrite(S0, HIGH); //20% scalling
  digitalWrite(S1, LOW);
  topServo.attach(9);
  bottomServo.attach(10);
  Serial.begin(9600);
}

void loop() {
  topServo.write(83); //set top servo at the first hole to catch the candy
  delay(500);
  
  for(int i = 83; i >= 30; i--) { //move top servo with the candy to the color sensor position
    topServo.write(i);
    delay(2);
  }
  delay(500);
  
  color = readColor(); //read the value from color sensor and put the bottom servo in the right path
  delay(10);  
  switch (color) {
    case 1:
    bottomServo.write(15);
    break;
    case 2:
    bottomServo.write(60);
    break;
    case 3:
    bottomServo.write(110);
    break;
   
    case 0:
    break;
  }
  delay(300);
  
  for(int i = 30; i >= 0; i--) { //move top servo with candy from the color sensor position to the second hole position
    topServo.write(i);
    delay(2);
  } 
  delay(200);
  
  for(int i = 0; i <= 83; i++) { //return top servo to the first position to catch another candy
    topServo.write(i);
    delay(2);
  }
  color=0;
}

int readColor() { //color sensor function to read the color
  
  // Setting red
  digitalWrite(S2, LOW);
  digitalWrite(S3, LOW);
  frequency = pulseIn(sensorOut, LOW);
  int R = frequency;
  Serial.print("R= ");
  Serial.print(frequency);
  Serial.print("  ");
  delay(50);
  
  // Setting Green
  digitalWrite(S2, HIGH);
  digitalWrite(S3, HIGH);
  frequency = pulseIn(sensorOut, LOW);
  int G = frequency;
  Serial.print("G= ");
  Serial.print(frequency);
  Serial.print("  ");
  delay(50);
  
  // Setting Blue
  digitalWrite(S2, LOW);
  digitalWrite(S3, HIGH);
  frequency = pulseIn(sensorOut, LOW);
  int B = frequency;
  Serial.print("B= ");
  Serial.print(frequency);
  Serial.println("  ");
  delay(50);
  
  if(R<65 & R>50 & G>83 & G<95 & B>60 & B<70){
    color = 1; // Red
  }
  if(G<70 & G>55 & R<75 & R>65 &B<65 & B>54){
    color = 2; // Green
  }
  if (B<60 &B>40 & G>68 & G<85 & R>75 & R<95){
    color = 3; // Blue
  }
  return color;  
}
/*i hope this was helpful for you please check tutorial video in my youtube channel*/
/*and if you have any question i will be happy answering it :)*/
/*Servo tutorial : https://youtu.be/FXCSVss93XU*/
/*Color Sensor tutorial : https://youtu.be/IqVtrWKNfCw*/
/* https://www.youtube.com/playlist?list=PLJRh_zZSG_PT0lJAzx0eTCyPwk_obpJjt */

This documentation provides a comprehensive overview of the circuit, including the components used, their wiring details, and the code running on the Arduino UNO.