Cirkit Designer LogoCirkit DesignerYour all-in-one circuit design IDE Launch Cirkit Designer App

Arduino UNO and L298N Bluetooth Controlled Robotic Car

View and Edit Project In Cirkit DesignerImage of Arduino UNO and L298N Bluetooth Controlled Robotic Car

Circuit Documentation

Summary

This document provides a detailed overview of a Bluetooth-controlled car circuit. The circuit includes an Arduino UNO microcontroller, an L298N DC motor driver, a 12V battery, multiple motors with wheels, and an HC-05 Bluetooth module. The Arduino UNO is programmed to control the motors based on commands received via Bluetooth.

Component List

  1. L298N DC Motor Driver

    • Description: Dual H-Bridge motor driver
    • Pins: OUT1, OUT2, 12V, GND, 5V, OUT3, OUT4, 5V-ENA-JMP-I, 5V-ENA-JMP-O, +5V-J1, +5V-J2, ENA, IN1, IN2, IN3, IN4, ENB

  2. Arduino UNO

    • Description: Microcontroller board based on the ATmega328P
    • Pins: UNUSED, IOREF, Reset, 3.3V, 5V, GND, Vin, A0, A1, A2, A3, A4, A5, SCL, SDA, AREF, D13, D12, D11, D10, D9, D8, D7, D6, D5, D4, D3, D2, D1, D0

  3. HC-05 Bluetooth Module

    • Description: Bluetooth module for wireless communication
    • Pins: EN, VCC, GND, TXD, RXD, STATE

  4. Battery 12V

    • Description: Power source
    • Pins: +, -

  5. Motor and Wheels

    • Description: DC motors with attached wheels
    • Pins: vcc, GND

Wiring Details

L298N DC Motor Driver

Arduino UNO

HC-05 Bluetooth Module

Battery 12V

Motor and Wheels

Documented Code

Arduino UNO Code

//Arduino Bluetooth Controlled Car
//Before uploading the code you have to install the necessary library
//Note - Disconnect the Bluetooth Module before hitting the upload button otherwise you'll get a compilation error message.
//AFMotor Library https://learn.adafruit.com/adafruit-motor-shield/library-install 
//After downloading the library open Arduino IDE >> go to sketch >> Include Library >> ADD. ZIP Library >> Select the downloaded 
//ZIP File >> Open it >> Done
//Now You Can Upload the Code without any problem but make sure the bt module isn't connected with Arduino while uploading code

#include <AFMotor.h>

//initial motors pin
AF_DCMotor motor1(1, MOTOR12_1KHZ); 
AF_DCMotor motor2(2, MOTOR12_1KHZ); 
AF_DCMotor motor3(3, MOTOR34_1KHZ);
AF_DCMotor motor4(4, MOTOR34_1KHZ);

char command; 

void setup() 
{       
  Serial.begin(9600);  //Set the baud rate to your Bluetooth module.
}

void loop(){
  if(Serial.available() > 0){ 
    command = Serial.read(); 
    Stop(); //initialize with motors stopped
    //Change pin mode only if new command is different from previous.   
    //Serial.println(command);
    switch(command){
    case 'F':  
      forward();
      break;
    case 'B':  
       back();
      break;
    case 'L':  
      left();
      break;
    case 'R':
      right();
      break;
    }
  } 
}

void forward()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(FORWARD); //rotate the motor clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(FORWARD); //rotate the motor clockwise
  motor3.setSpeed(255);//Define maximum velocity
  motor3.run(FORWARD); //rotate the motor clockwise
  motor4.setSpeed(255);//Define maximum velocity
  motor4.run(FORWARD); //rotate the motor clockwise
}

void back()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(BACKWARD); //rotate the motor anti-clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(BACKWARD); //rotate the motor anti-clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(BACKWARD); //rotate the motor anti-clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(BACKWARD); //rotate the motor anti-clockwise
}

void left()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(BACKWARD); //rotate the motor anti-clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(BACKWARD); //rotate the motor anti-clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(FORWARD);  //rotate the motor clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(FORWARD);  //rotate the motor clockwise
}

void right()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(FORWARD); //rotate the motor clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(FORWARD); //rotate the motor clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(BACKWARD); //rotate the motor anti-clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(BACKWARD); //rotate the motor anti-clockwise
} 

void Stop()
{
  motor1.setSpeed(0); //Define minimum velocity
  motor1.run(RELEASE); //stop the motor when release the button
  motor2.setSpeed(0); //Define minimum velocity
  motor2.run(RELEASE); //rotate the motor clockwise
  motor3.setSpeed(0); //Define minimum velocity
  motor3.run(RELEASE); //stop the motor when release the button
  motor4.setSpeed(0); //Define minimum velocity
  motor4.run(RELEASE); //stop the motor when release the button
}

Arduino Mega 2560 Code

void setup() {
  // put your setup code here, to run once:

}

void loop()