Interactive Touch and Motion Sensor System with Bela Board and OLED Display
View and Edit Project In Cirkit Designer
Circuit Documentation
Summary
This document provides a detailed overview of a circuit design that includes various components such as a TRILL CRAFT sensor, copper tape, a vibration motor, an accelerometer (ADXXL335), a loudspeaker, a pushbutton, a resistor, an OLED display, and a Bela Board Rev C. The circuit is designed to interface these components for a specific application, with connections detailed in the following sections.
Component List
TRILL CRAFT
- Pins: GND, VCC, SDA, SCL, 0, 15, 14, 29, 22, 7
- Description: Not provided
- Purpose in Circuit: Not provided
Copper Tape
- Pins: Touch
- Description: Not provided
- Purpose in Circuit: Not provided
Vibration Motor
- Pins: POS, NEG
- Description: Not provided
- Purpose in Circuit: Not provided
ADXXL335 (Accelerometer)
- Pins: VCC, X-OUT, Y-OUT, Z-OUT, GND
- Description: Not provided
- Purpose in Circuit: Not provided
Loudspeaker
- Pins: pin1, pin2
- Description: Not provided
- Purpose in Circuit: Not provided
Pushbutton
- Pins: Pin 3 (out), Pin 4 (out), Pin 1 (in), Pin 2 (in)
- Description: Not provided
- Purpose in Circuit: Not provided
Resistor
- Pins: pin1, pin2
- Description: Not provided
- Purpose in Circuit: Not provided
- Properties: Resistance: 10000 Ohms
0.96" OLED Display
- Pins: GND, VDD, SCK, SDA
- Description: Not provided
- Purpose in Circuit: Not provided
Bela Board Rev C
- Pins: GND, 3.3V, 5V, I2C-1 SCL, I2C-1 SDA, AUDIO OUT LEFT, AUDIO OUT RIGHT, Digital 0, Digital 1, Analog IN 0, Analog IN 1, Analog IN 2, Analog IN 3, Analog IN 4, Speaker Left, Speaker RIGHT
- Description: Not provided
- Purpose in Circuit: Not provided
Alligator Clip Cable (Blue)
- Pins: Pin, Alligator
- Description: Not provided
- Purpose in Circuit: Not provided
Wiring Details
TRILL CRAFT
VCC is connected to:
- Resistor pin2
- Bela Board Rev C 3.3V
- OLED VDD
GND is connected to:
- Pushbutton Pin 4 (out)
- Pushbutton Pin 2 (in)
- Bela Board Rev C GND
- Vibration Motor NEG
- OLED GND
- ADXXL335 GND
SDA is connected to:
- Bela Board Rev C I2C-1 SDA
- OLED SDA
SCL is connected to:
- Bela Board Rev C I2C-1 SCL
- OLED SCK
Pin 0 is connected to:
- Alligator Clip Cable (Blue) Alligator
Pin 15 is connected to:
- Alligator Clip Cable (Blue) Alligator
Pin 29 is connected to:
- Alligator Clip Cable (Blue) Alligator
Copper Tape
- Touch is connected to:
- Alligator Clip Cable (Blue) Pin
Vibration Motor
POS is connected to:
- Bela Board Rev C Digital 0
NEG is connected to:
- TRILL CRAFT GND
- Pushbutton Pin 4 (out)
- Pushbutton Pin 2 (in)
- Bela Board Rev C GND
- OLED GND
- ADXXL335 GND
ADXXL335 (Accelerometer)
VCC is connected to:
- Bela Board Rev C 5V
X-OUT is connected to:
- Bela Board Rev C Analog IN 0
Y-OUT is connected to:
- Bela Board Rev C Analog IN 1
Z-OUT is connected to:
- Bela Board Rev C Analog IN 2
GND is connected to:
- TRILL CRAFT GND
- Pushbutton Pin 4 (out)
- Pushbutton Pin 2 (in)
- Bela Board Rev C GND
- Vibration Motor NEG
- OLED GND
Loudspeaker
pin1 is connected to:
- Bela Board Rev C Speaker Left
pin2 is connected to:
- Bela Board Rev C Speaker RIGHT
Pushbutton
Pin 3 (out) is connected to:
- Pushbutton Pin 1 (in)
- Resistor pin1
- Bela Board Rev C Digital 1
Pin 4 (out) is connected to:
- Pushbutton Pin 2 (in)
- TRILL CRAFT GND
- Bela Board Rev C GND
- Vibration Motor NEG
- OLED GND
- ADXXL335 GND
Resistor
pin1 is connected to:
- Pushbutton Pin 3 (out)
- Pushbutton Pin 1 (in)
- Bela Board Rev C Digital 1
pin2 is connected to:
- TRILL CRAFT VCC
- Bela Board Rev C 3.3V
- OLED VDD
0.96" OLED Display
VDD is connected to:
- Resistor pin2
- TRILL CRAFT VCC
- Bela Board Rev C 3.3V
GND is connected to:
- TRILL CRAFT GND
- Pushbutton Pin 4 (out)
- Pushbutton Pin 2 (in)
- Bela Board Rev C GND
- Vibration Motor NEG
- ADXXL335 GND
SCK is connected to:
- TRILL CRAFT SCL
- Bela Board Rev C I2C-1 SCL
SDA is connected to:
- TRILL CRAFT SDA
- Bela Board Rev C I2C-1 SDA
Bela Board Rev C
3.3V is connected to:
- Resistor pin2
- TRILL CRAFT VCC
- OLED VDD
5V is connected to:
- ADXXL335 VCC
GND is connected to:
- TRILL CRAFT GND
- Pushbutton Pin 4 (out)
- Pushbutton Pin 2 (in)
- Vibration Motor NEG
- OLED GND
- ADXXL335 GND
I2C-1 SCL is connected to:
- TRILL CRAFT SCL
- OLED SCK
I2C-1 SDA is connected to:
- TRILL CRAFT SDA
- OLED SDA
Digital 0 is connected to:
- Vibration Motor POS
Digital 1 is connected to:
- Pushbutton Pin 3 (out)
- Pushbutton Pin 1 (in)
- Resistor pin1
Analog IN 0 is connected to:
- ADXXL335 X-OUT
Analog IN 1 is connected to:
- ADXXL335 Y-OUT
Analog IN 2 is connected to:
- ADXXL335 Z-OUT
Speaker Left is connected to:
- Loudspeaker pin1
Speaker RIGHT is connected to:
- Loudspeaker pin2
Alligator Clip Cable (Blue)
Alligator is connected to:
- TRILL CRAFT Pin 0
- TRILL CRAFT Pin 15
- TRILL CRAFT Pin 29
Pin is connected to:
- Copper Tape Touch
Code
No code is provided for this circuit.
This document provides a comprehensive overview of the circuit, including a detailed list of components and their connections. This should serve as a useful reference for understanding and replicating the circuit design.