Circuit Documentation

Summary

This document provides a detailed overview of a circuit that includes an Arduino 101 microcontroller, pushbuttons for start and stop functions, a pilot lamp, a DC motor controller, a socket, and a DC power source. The circuit is designed to control a DC motor using the Arduino 101, with start and stop functionalities managed by pushbuttons and visual feedback provided by a pilot lamp.

Component List

1. Arduino 101

   • Description: Microcontroller board based on the Intel Curie module.
   • Pins: A5/SCL, A4/SDA, AREF, GND, D13/SCK, D12/MISO, D11 PWM/MOSI, D10 PWM/SS, D9 PWM, D8, D7, D6 PWM, D5 PWM, D4, D3 PWM, D2, D1/TX, D0/RX, AIN, ioref, RESET, 3V3, 5V, VIN, A0, A1, A2, A3, ICSP MISO, ICSP SCK, ICSP MOSI

2. Pushbutton START

   • Description: Pushbutton used to start the motor.
   • Pins: NC, NO

3. Pushbutton STOP

   • Description: Pushbutton used to stop the motor.
   • Pins: NC, NO

4. Pilot lamp blue

   • Description: Blue pilot lamp used for visual feedback.
   • Pins: x1, x2

5. BDC PWM DC MOTOR CONTROLLER 10A 6-90V

   • Description: DC motor controller capable of handling 10A and 6-90V.
   • Pins: + power, - power, + motor, - motor, GND, 0-5V, 5V

6. Socket

   • Description: Electrical socket for power supply.
   • Pins: Green, Life, Neutral

7. DC Power Source

   • Description: DC power source for the motor.
   • Pins: Ground, Positive

Wiring Details

Arduino 101

• D13/SCK is connected to x1 of the Pilot lamp blue.
• D3 PWM is connected to NO of the Pushbutton STOP and 5V of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.
• D2 is connected to NO of the Pushbutton START.
• GND is connected to NC of the Pushbutton STOP, GND of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V, x2 of the Pilot lamp blue, and NC of the Pushbutton START.

Pushbutton START

• NO is connected to D2 of the Arduino 101.
• NC is connected to GND of the Arduino 101.

Pushbutton STOP

• NO is connected to D3 PWM of the Arduino 101 and 5V of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.
• NC is connected to GND of the Arduino 101 and GND of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.

Pilot lamp blue

• x1 is connected to D13/SCK of the Arduino 101.
• x2 is connected to GND of the Arduino 101.

BDC PWM DC MOTOR CONTROLLER 10A 6-90V

• + power is connected to Life of the Socket.
• - power is connected to Neutral of the Socket.
• + motor is connected to Positive of the DC Power Source.
• - motor is connected to Ground of the DC Power Source.
• GND is connected to NC of the Pushbutton STOP and GND of the Arduino 101.
• 5V is connected to NO of the Pushbutton STOP and D3 PWM of the Arduino 101.

Socket

• Life is connected to + power of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.
• Neutral is connected to - power of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.

DC Power Source

• Positive is connected to + motor of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.
• Ground is connected to - motor of the BDC PWM DC MOTOR CONTROLLER 10A 6-90V.

Documented Code

Arduino 101 Code (sketch.ino)

void setup() {
  // put your setup code here, to run once:

}

void loop() {
  // put your main code here, to run repeatedly:

}

Additional Documentation (documentation.txt)