Circuit Documentation

Summary

This document provides a detailed overview of a circuit that includes various components such as an Arduino Nano, NRF24L01 Adapter, Joystick modules, a potentiometer, an LED, a resistor, a rocker switch, a toggle switch, a battery, and an electrolytic capacitor. The circuit is designed to interface with a microcontroller to perform various functions, including reading joystick inputs, controlling an LED, and communicating wirelessly using the NRF24L01 module.

Component List

Arduino Nano

• Description: A small, complete, and breadboard-friendly board based on the ATmega328P.
• Pins: D1/TX, D0/RX, RESET, GND, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11/MOSI, D12/MISO, VIN, 5V, A7, A6, A5, A4, A3, A2, A1, A0, AREF, 3V3, D13/SCK

NRF24L01 Adapter

• Description: An adapter for the NRF24L01 wireless transceiver module.
• Pins: CE, CSN, SCK, MOSI, MISO, IRQ, VCC, GND

Electrolytic Capacitor

• Description: A capacitor with a capacitance of 100,000,000 Farads.
• Pins: -, +

Joystick Module

• Description: A module with a joystick for directional input.
• Pins: SW, VRY, VRX, VCC, GND

Potentiometer

• Description: A variable resistor used to adjust voltage levels.
• Pins: GND, Output, VCC

LED: Two Pin (red)

• Description: A red LED with two pins.
• Pins: cathode, anode

Resistor

• Description: A resistor with a resistance of 200 Ohms.
• Pins: pin1, pin2

Rocker Switch

• Description: A switch that can toggle between two states.
• Pins: output, input

Toggle Switch

• Description: A switch that can toggle between two states.
• Pins: Vcc, Sig, Gnd

Battery

• Description: A power source for the circuit.
• Pins: -, +

Wiring Details

Arduino Nano

• GND: Connected to the GND pins of the Potentiometer, Electrolytic Capacitor, Joystick modules, NRF24L01 Adapter, Toggle Switch, and LED cathode.
• D2: Connected to the Sig pin of the Toggle Switch.
• D7: Connected to the CE pin of the NRF24L01 Adapter.
• D8: Connected to the CSN pin of the NRF24L01 Adapter.
• D11/MOSI: Connected to the MOSI pin of the NRF24L01 Adapter.
• D12/MISO: Connected to the MISO pin of the NRF24L01 Adapter.
• VIN: Connected to the input pin of the Rocker Switch and pin2 of the Resistor.
• 5V: Connected to the VCC pins of the Potentiometer, Electrolytic Capacitor, Joystick modules, and NRF24L01 Adapter.
• A7: Connected to the Output pin of the Potentiometer.
• A3: Connected to the VRX pin of the Joystick module.
• A2: Connected to the VRY pin of the Joystick module.
• A1: Connected to the VRX pin of the second Joystick module.
• A0: Connected to the VRY pin of the second Joystick module.
• D13/SCK: Connected to the SCK pin of the NRF24L01 Adapter.

NRF24L01 Adapter

• GND: Connected to the GND pin of the Arduino Nano.
• CE: Connected to the D7 pin of the Arduino Nano.
• CSN: Connected to the D8 pin of the Arduino Nano.
• SCK: Connected to the D13/SCK pin of the Arduino Nano.
• MOSI: Connected to the D11/MOSI pin of the Arduino Nano.
• MISO: Connected to the D12/MISO pin of the Arduino Nano.
• VCC: Connected to the 5V pin of the Arduino Nano.

Electrolytic Capacitor

• -: Connected to the GND pin of the Arduino Nano.
• +: Connected to the 5V pin of the Arduino Nano.

Joystick Module

• GND: Connected to the GND pin of the Arduino Nano.
• VCC: Connected to the 5V pin of the Arduino Nano.
• VRX: Connected to the A3 pin of the Arduino Nano.
• VRY: Connected to the A2 pin of the Arduino Nano.

Second Joystick Module

• GND: Connected to the GND pin of the Arduino Nano.
• VCC: Connected to the 5V pin of the Arduino Nano.
• VRX: Connected to the A1 pin of the Arduino Nano.
• VRY: Connected to the A0 pin of the Arduino Nano.

Potentiometer

• GND: Connected to the GND pin of the Arduino Nano.
• Output: Connected to the A7 pin of the Arduino Nano.
• VCC: Connected to the 5V pin of the Arduino Nano.

LED: Two Pin (red)

• cathode: Connected to the GND pin of the Arduino Nano.
• anode: Connected to pin1 of the Resistor.

Resistor

• pin1: Connected to the anode of the LED.
• pin2: Connected to the VIN pin of the Arduino Nano.

Rocker Switch

• input: Connected to the VIN pin of the Arduino Nano.
• output: Connected to the + pin of the Battery.

Toggle Switch

• Gnd: Connected to the GND pin of the Arduino Nano.
• Sig: Connected to the D2 pin of the Arduino Nano.
• Vcc: Connected to the 5V pin of the Arduino Nano.

Battery

• -: Connected to the GND pin of the Arduino Nano.
• +: Connected to the output pin of the Rocker Switch.

Documented Code

Arduino Nano Code (sketch.ino)

void setup() {
  // put your setup code here, to run once:

}

void loop() {
  // put your main code here, to run repeatedly:

}

Documentation (documentation.txt)

This document provides a comprehensive overview of the circuit, including the components used, their connections, and the code running on the microcontroller.