Arduino Nano-Controlled Dual Motor Driver System with Pushbutton Interface
View and Edit Project In Cirkit Designer
Circuit Documentation
Summary
This circuit integrates various components controlled by an Arduino Nano microcontroller to perform a set of functions. The circuit includes a motor driver (L298N) to control two DC Mini Metal Gear Motors, a MUX (Multiplexer) for signal routing, a boost converter (MT3608) to step up the voltage, and a power source consisting of two 18650 batteries. User inputs are captured through two pushbuttons, and a toggle switch is used to control the power flow from the batteries to the boost converter.
Component List
Microcontroller
- Arduino Nano: A compact microcontroller board based on the ATmega328P, featuring digital and analog I/O pins.
Motor Driver
- L298N DC Motor Driver: A module capable of driving two DC motors with control inputs for speed and direction.
Motors
- DC Mini Metal Gear Motor: Two small DC motors with gear reduction for increased torque.
Power Management
- Boost Converter MT3608: A step-up voltage regulator that boosts the input voltage to a higher level.
- 2x 18650 Batteries: Lithium-ion rechargeable batteries providing the power source for the circuit.
- Toggle Switch: A switch to control the connection between the batteries and the boost converter.
User Input
- Pushbutton: Two simple pushbuttons used for user input.
Signal Routing
- MUX (Multiplexer): A device that selects one of many input signals and forwards the selected input into a single line.
Wiring Details
Arduino Nano
- Digital Pins:
- D2 connected to Pushbutton 1
- D3 connected to Pushbutton 2
- D6 connected to L298N Motor Driver (ENB)
- D7 connected to L298N Motor Driver (IN4)
- D8 connected to L298N Motor Driver (IN3)
- D9 connected to L298N Motor Driver (IN2)
- D10 connected to L298N Motor Driver (IN1)
- D11/MOSI connected to L298N Motor Driver (ENA)
- Analog Pins:
- A0 connected to MUX (SIG)
- A1 connected to MUX (D)
- A2 connected to MUX (C)
- A3 connected to MUX (B)
- A4 connected to MUX (A)
- Power Pins:
- 5V connected to MUX (V) and L298N Motor Driver (5V)
- GND connected to Pushbuttons, MUX (G), and L298N Motor Driver (GND)
L298N DC Motor Driver
- Motor Outputs:
- OUT1 and OUT2 connected to Motor 1
- OUT3 and OUT4 connected to Motor 2
- Power Input:
- 12V connected to Boost Converter (OUTPUT +)
- GND connected to common ground
DC Mini Metal Gear Motor 1 & 2
- Motor 1:
- IN1 and IN2 connected to L298N Motor Driver (OUT1 and OUT2)
- Motor 2:
- IN1 and IN2 connected to L298N Motor Driver (OUT3 and OUT4)
Boost Converter MT3608
- Input:
- INPUT + connected to Toggle Switch (COM)
- INPUT - connected to 18650 Batteries (gnd)
- Output:
- OUTPUT + connected to L298N Motor Driver (12V)
- OUTPUT - connected to common ground
2x 18650 Batteries
- Power Output:
- vcc connected to Toggle Switch (L1)
- gnd connected to common ground
Toggle Switch
- Connections:
- L1 connected to 18650 Batteries (vcc)
- COM connected to Boost Converter (INPUT +)
Pushbutton 1
- Connections:
- Pin 2 connected to Arduino Nano (D2)
- Pin 3 connected to common ground
Pushbutton 2
- Connections:
- Pin 2 connected to Arduino Nano (D3)
- Pin 3 connected to common ground
MUX (Multiplexer)
- Control Inputs:
- A connected to Arduino Nano (A4)
- B connected to Arduino Nano (A3)
- C connected to Arduino Nano (A2)
- D connected to Arduino Nano (A1)
- Signal Output:
- SIG connected to Arduino Nano (A0)
- Power:
- V connected to Arduino Nano (5V)
- G connected to common ground
Documented Code
Arduino Nano Code (sketch.ino)
void setup() {
// put your setup code here, to run once:
}
void loop() {
// put your main code here, to run repeatedly:
}
Additional Notes (documentation.txt)
No additional code documentation provided.