Circuit Documentation

Summary

This document provides a detailed overview of a circuit designed to interface various sensors with an Arduino UNO R4 WiFi microcontroller. The circuit includes a TDS sensor, a DS18B20 temperature sensor, a pH degree sensor module, and a turbidity sensor. The sensors are connected to the Arduino for data acquisition and processing.

Component List

Sonda Sensor TDS

• Description: Measures Total Dissolved Solids (TDS) in water.
• Pins: +, -

DS18B20

• Description: Digital temperature sensor.
• Pins: signal, GND, vcc

TDS Sensor

• Description: Measures the electrical conductivity of water to determine TDS.
• Pins: P1, P2, +, -, A

Resistor

• Description: Provides resistance in the circuit.
• Pins: pin1, pin2
• Properties: Resistance: 4.7 Ohms

pH Degree Sensor Module

• Description: Measures the pH level of a solution.
• Pins: pH Negative, pH Positive, pH A

Modulo Sensor TDS

• Description: Module for interfacing the TDS sensor.
• Pins: A, -, +

Sonda Sensor Turbidez / Turbidity

• Description: Measures the turbidity (cloudiness) of water.
• Pins: S, -, +

Arduino UNO R4 WiFi

• Description: Microcontroller board with WiFi capabilities.
• Pins: OFF, GND, VRTC, IIC0_SCL, IIC0_SDA, 3V3, GPIO 41, GPIO 0, GPIO 42, GPIO 43, GPIO 44, BOOT, IOREF, RESET, 5V, VIN, A0, A1, A2, A3, A4, A5, RSPCKA, CIPO, COPI, D0/RX, D1/TX, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, AREF, SDA, SCL

Wiring Details

Sonda Sensor TDS

• Pin - connected to TDS Sensor P1
• Pin + connected to TDS Sensor P2

DS18B20

• Pin vcc connected to Arduino UNO R4 WiFi 5V
• Pin GND connected to Arduino UNO R4 WiFi GND
• Pin signal connected to Arduino UNO R4 WiFi D2 through Resistor pin2

TDS Sensor

• Pin P1 connected to Sonda Sensor TDS -
• Pin P2 connected to Sonda Sensor TDS +
• Pin + connected to Arduino UNO R4 WiFi 5V
• Pin - connected to Arduino UNO R4 WiFi GND
• Pin A connected to Arduino UNO R4 WiFi A0

Resistor

• Pin pin1 connected to Arduino UNO R4 WiFi 5V
• Pin pin2 connected to Arduino UNO R4 WiFi D2 and DS18B20 signal

pH Degree Sensor Module

• Pin pH Positive connected to Arduino UNO R4 WiFi 5V
• Pin pH Negative connected to Arduino UNO R4 WiFi GND
• Pin pH A connected to Arduino UNO R4 WiFi A2

Modulo Sensor TDS

• Pin + connected to Arduino UNO R4 WiFi 5V and Sonda Sensor Turbidez / Turbidity +
• Pin - connected to Arduino UNO R4 WiFi GND and Sonda Sensor Turbidez / Turbidity -
• Pin A connected to Arduino UNO R4 WiFi A1

Sonda Sensor Turbidez / Turbidity

• Pin + connected to Modulo Sensor TDS +
• Pin - connected to Modulo Sensor TDS -
• Pin S not connected

Arduino UNO R4 WiFi

• Pin 5V connected to Modulo Sensor TDS +, Resistor pin1, DS18B20 vcc, pH Degree Sensor Module pH Positive, TDS Sensor +
• Pin GND connected to Modulo Sensor TDS -, DS18B20 GND, pH Degree Sensor Module pH Negative, TDS Sensor -
• Pin A0 connected to TDS Sensor A
• Pin D2 connected to Resistor pin2 and DS18B20 signal
• Pin A2 connected to pH Degree Sensor Module pH A
• Pin A1 connected to Modulo Sensor TDS A

Documented Code

Arduino UNO R4 WiFi Code

void setup() {
  // put your setup code here, to run once:

}

void loop() {
  // put your main code here, to run repeatedly:

}

Additional Documentation

This document provides a comprehensive overview of the circuit, including a detailed list of components, their wiring connections, and the code used for the Arduino UNO R4 WiFi microcontroller.