Cirkit Designer LogoCirkit DesignerYour all-in-one circuit design IDE Launch Cirkit Designer App

Arduino UNO Bluetooth Controlled Car with L298N Motor Driver

View and Edit Project In Cirkit DesignerImage of Arduino UNO Bluetooth Controlled Car with L298N Motor Driver

Circuit Documentation

Summary

This document provides a detailed overview of a Bluetooth-controlled car circuit. The circuit consists of an Arduino UNO microcontroller, an L298N DC motor driver, four DC motors with wheels, an HC-05 Bluetooth module, and a 12V battery. The Arduino UNO is programmed to control the motors based on commands received via Bluetooth.

Component List

  1. L298N DC Motor Driver

    • Description: A dual H-Bridge motor driver that allows control of the speed and direction of two DC motors.
    • Pins: OUT1, OUT2, 12V, GND, 5V, OUT3, OUT4, 5V-ENA-JMP-I, 5V-ENA-JMP-O, +5V-J1, +5V-J2, ENA, IN1, IN2, IN3, IN4, ENB

  2. Arduino UNO

    • Description: A microcontroller board based on the ATmega328P, used for various embedded applications.
    • Pins: UNUSED, IOREF, Reset, 3.3V, 5V, GND, Vin, A0, A1, A2, A3, A4, A5, SCL, SDA, AREF, D13, D12, D11, D10, D9, D8, D7, D6, D5, D4, D3, D2, D1, D0

  3. HC-05 Bluetooth Module

    • Description: A Bluetooth module used for wireless communication between the Arduino and a Bluetooth-enabled device.
    • Pins: EN, VCC, GND, TXD, RXD, STATE

  4. Battery 12V

    • Description: A 12V battery used to power the motor driver and motors.
    • Pins: +, -

  5. Motor and Wheels (4 units)

    • Description: DC motors with attached wheels used for driving the car.
    • Pins: vcc, GND

Wiring Details

L298N DC Motor Driver

Arduino UNO

HC-05 Bluetooth Module

Battery 12V

Motor and Wheels

Documented Code

//Arduino Bluetooth Controlled Car
//Before uploading the code you have to install the necessary library
//Note - Disconnect the Bluetooth Module before hitting the upload button otherwise you'll get a compilation error message.
//AFMotor Library https://learn.adafruit.com/adafruit-motor-shield/library-install 
//After downloading the library open Arduino IDE >> go to sketch >> Include Library >> ADD. ZIP Library >> Select the downloaded 
//ZIP File >> Open it >> Done
//Now You Can Upload the Code without any problem but make sure the bt module isn't connected with Arduino while uploading code

#include <AFMotor.h>

//initial motors pin
AF_DCMotor motor1(1, MOTOR12_1KHZ); 
AF_DCMotor motor2(2, MOTOR12_1KHZ); 
AF_DCMotor motor3(3, MOTOR34_1KHZ);
AF_DCMotor motor4(4, MOTOR34_1KHZ);

char command; 

void setup() 
{       
  Serial.begin(9600);  //Set the baud rate to your Bluetooth module.
}

void loop(){
  if(Serial.available() > 0){ 
    command = Serial.read(); 
    Stop(); //initialize with motors stopped
    //Change pin mode only if new command is different from previous.   
    //Serial.println(command);
    switch(command){
    case 'F':  
      forward();
      break;
    case 'B':  
       back();
      break;
    case 'L':  
      left();
      break;
    case 'R':
      right();
      break;
    }
  } 
}

void forward()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(FORWARD); //rotate the motor clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(FORWARD); //rotate the motor clockwise
  motor3.setSpeed(255);//Define maximum velocity
  motor3.run(FORWARD); //rotate the motor clockwise
  motor4.setSpeed(255);//Define maximum velocity
  motor4.run(FORWARD); //rotate the motor clockwise
}

void back()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(BACKWARD); //rotate the motor anti-clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(BACKWARD); //rotate the motor anti-clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(BACKWARD); //rotate the motor anti-clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(BACKWARD); //rotate the motor anti-clockwise
}

void left()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(BACKWARD); //rotate the motor anti-clockwise
  motor2.setSpeed(255); //Define maximum velocity
  motor2.run(BACKWARD); //rotate the motor anti-clockwise
  motor3.setSpeed(255); //Define maximum velocity
  motor3.run(FORWARD);  //rotate the motor clockwise
  motor4.setSpeed(255); //Define maximum velocity
  motor4.run(FORWARD);  //rotate the motor clockwise
}

void right()
{
  motor1.setSpeed(255); //Define maximum velocity
  motor1.run(FORWARD);