Circuit Documentation

Summary

This document provides a detailed overview of a circuit that includes an Arduino UNO microcontroller, a TCS3200 color sensor, and two LEDs (red and green) with associated resistors. The circuit is designed to interface the color sensor with the Arduino and control the LEDs based on the sensor's output.

Component List

Arduino UNO

• Description: A microcontroller board based on the ATmega328P.
• Pins: UNUSED, IOREF, Reset, 3.3V, 5V, GND, Vin, A0, A1, A2, A3, A4, A5, SCL, SDA, AREF, D13, D12, D11, D10, D9, D8, D7, D6, D5, D4, D3, D2, D1, D0

TCS3200 Color Sensor

• Description: A color sensor that can detect and measure the intensity of red, green, and blue light.
• Pins: GND, OUT, S2, S3, VCC, LED, S0, S1

LED: Two Pin (Red)

• Description: A standard red LED.
• Pins: cathode, anode

LED: Two Pin (Green)

• Description: A standard green LED.
• Pins: cathode, anode

Resistor (220 Ohms)

• Description: A resistor with a resistance of 220 Ohms.
• Pins: pin1, pin2
• Properties:
  • Resistance: 220 Ohms

Wiring Details

Arduino UNO

• GND: Connected to the anode of the red LED, the anode of the green LED, and the GND pin of the TCS3200 color sensor.
• 5V: Connected to the VCC pin of the TCS3200 color sensor.
• A0: Connected to pin1 of a 220 Ohm resistor, which is connected to the cathode of the red LED.
• A4: Connected to pin1 of a 220 Ohm resistor, which is connected to the cathode of the green LED.
• D2: Connected to the S0 pin of the TCS3200 color sensor.
• D3: Connected to the S1 pin of the TCS3200 color sensor.
• D4: Connected to the S2 pin of the TCS3200 color sensor.
• D5: Connected to the S3 pin of the TCS3200 color sensor.
• D6: Connected to the OUT pin of the TCS3200 color sensor.

TCS3200 Color Sensor

• GND: Connected to the GND pin of the Arduino UNO.
• OUT: Connected to the D6 pin of the Arduino UNO.
• S2: Connected to the D4 pin of the Arduino UNO.
• S3: Connected to the D5 pin of the Arduino UNO.
• VCC: Connected to the 5V pin of the Arduino UNO.
• S0: Connected to the D2 pin of the Arduino UNO.
• S1: Connected to the D3 pin of the Arduino UNO.

LED: Two Pin (Red)

• cathode: Connected to pin1 of a 220 Ohm resistor, which is connected to the A0 pin of the Arduino UNO.
• anode: Connected to the GND pin of the Arduino UNO.

LED: Two Pin (Green)

• cathode: Connected to pin1 of a 220 Ohm resistor, which is connected to the A4 pin of the Arduino UNO.
• anode: Connected to the GND pin of the Arduino UNO.

Resistor (220 Ohms)

• Resistor 1:
  • pin1: Connected to the cathode of the red LED.
  • pin2: Connected to the A0 pin of the Arduino UNO.
• Resistor 2:
  • pin1: Connected to the cathode of the green LED.
  • pin2: Connected to the A4 pin of the Arduino UNO.

Documented Code

Arduino UNO Code (sketch.ino)

void setup() {
  // put your setup code here, to run once:

}

void loop() {
  // put your main code here, to run repeatedly:

}

This code is a basic template for the Arduino UNO. The setup() function is where you initialize your settings, and the loop() function is where the main code runs repeatedly. You can add your specific code to interface with the TCS3200 color sensor and control the LEDs based on the sensor's output.